|
The Secret Ingredient in Our Best Trumpets An MBS explainer for all musicians Look closely at our newest Summits and you'll spot it: a loop of grey, slightly textured metal where you'd expect shiny brass. That's not a styling choice. It's MBS, short for Multi-Bore-Shape, and it's the reason these horns make the upper register sing with very little effort. First, what's a bore? A trumpet is really one long tube of air, folded up so you can hold it. The bore is simply the inside of that tube: the space your air and sound travel through. On almost every trumpet ever made, the tuning slide is a plain round tube bent into a U. It's round because brass tubing comes round, and that's what bends easily in a shop. Nobody chose round because it sounds best. What MBS changes An MBS tube doesn't stay round. As it travels around the loop, its inside gradually morphs through several different shapes. What stays the same is the amount of room inside. The overall volume and air flow match a conventional slide, so the horn doesn't feel stuffy or blown-open. Same space for your air, just shaped with a purpose along the way. Why the shape matters
Shape changes how the horn answers back. When you play, a sound wave bounces back and forth inside the tube, and every bend and contour nudges it. Acousticians call that push-back impedance. When the horn's push-back lines up with what your lips are doing, notes lock in and speak easily. When it doesn't, you work harder for the same note, and you feel it most up high. Think of your own voice. You change from an "ooh" to an "ahh" without using more air; you just reshape your mouth. MBS does the same thing inside the trumpet. By shaping the tube, we can tune that push-back far more precisely than a plain round tube allows. Why it's 3D printed in stainless steel You can't bend a shape-shifting tube out of brass tubing. So we print every MBS part in metal, as one piece, exactly as designed. The metal is 316 stainless steel, the same alloy trusted in marine and food-processing equipment. It shrugs off corrosion, and printing lets us build the inside of the tube to shapes no traditional shop tool can reach. That's the grey, lightly textured finish you see in the photos. Where you'll find it The G4 Summit was the first MBS trumpet ever built. Today MBS shows up in two places on our horns:
Our Muse MMXX modular trumpet is also available in a Multi-Bore-Shape version. What you'll notice The short version: high notes take less work. Players who have fought the upper register for years often find it opening up, without changing their mouthpiece or their air. The best way to understand MBS is to play one. Call us at 303-657-2747 or stop by the Denver shop for a play-test. Where will you see it in the future I have plans to incorporate MBS technology design into leadpipes, pistons, and bells. Can you imagine how our trumpets will evolve over the next few years? I can... - Jason
0 Comments
I Just Played the First 3D-Printed Stainless Steel Trumpet Bell Today I put my very first 3D-printed stainless steel bell on a trumpet and played it. Honestly, this is something I didn't think would ever happen. I printed the bell in 316 stainless steel. There are a few supports on the underside, but the rest printed without them. I designed it for the Muse trumpet so I can screw it on and off and try different variations. As far as I know, this is the only one I've ever made and put on a Muse. No rim needed You'll see there's no bell rim. It doesn't need one as stainless steel is considerably more stable than brass. How it sounds There are a lot of ideas out there about what a stainless steel bell would sound like. The truth is, in this configuration it sounds very much like a copper bell, because I made it quite thick. If I thin it out, which I can do with my laser or by grinding and polishing, it will sound more like a brass bell. When I tap it, it has a beautiful ring that just keeps going until I touch it. A large taper bell This bell has a really big taper, bigger than normal, and in my opinion it gives a beautiful, warm sound. I played it with a #6 leadpipe. That's a relatively bright leadpipe, and with this big taper the setup is still very warm. Right away it had punch, and it was easy to play. I'm sure it's easier than a brass bell. Then I noticed I didn't have an insert in the VGR. Once I put one in, it was effortless. What's next I'm already working on a polished stainless steel bell in the same taper, and I'll be experimenting with a range of new tapers and multi-tapers. We will begin offering stainless steel bell tapers in standard, new, and prototype tapers and designs beginning in January 2027. And we will be focusing on producing only two models next year, the Muse and the G5 Summit. You will see the release of our new Flugelhorn as well. The Rumors, Dreams, Bravura, and G4 will all be retired. One more change to mention, we are upgrading the majority of our video releases. Get an exclusive, behind-the-scenes look at how we design, build, and research trumpets with our new premium subscription coming in January. |
Jason Harrelson
Inventor, Musician, Educator and Founder of Harrelson Trumpets, Trumpet Momentum and Harrelson Momentum. Archives
October 2026
|
RSS Feed
